June 21, 2019
Make sure the impeller is free to move
Make sure the impeller is free to move and that nothing is lodged. If you hear
metallic noises or loud vibrations then this is a sign of some internal problem.
Don't get trapped into buying the same pump if it has failed unexpectedly.
Properly inspecting your pump can reduce the risk of damages. If you find you
are almost burning your hand then there may be a problem. The bearings might be
loose or seized. However, it should not be hot when running on low speed. It is
worth the investment to buy a premium pump as they run quieter, consume less
energy and last longer. Choose the same port size, 1 1/2" or 2". If you pump
hums and or the main breaker trips then the capacitor may be shot. A failed hot
tub pump can cost the owner 100's if not 1000's of dollars in extra damages. If
that looks good then you should inspect the inside of the pump housing. All pump
manufacturers make similar replacement pumps so look for quality when selecting
a new pump. It may be time to replace!
A spa pump has a starting capacitor that gives it extra juice when starting. Is your pump a one speed or two speed pump? Finally, match the amp rating of your pump closely to the amps of another pump. Look for signs of wear and tear and be proactive!
I always suggest you look for signs of wear every time you replace or clean you filter system.
While poor jet performance may be caused by a pump, it is not likely. A spa pump either works or does not work. At this time, have a good look at the spa pump. I would look 1st to a plugged filter or a clogged intake as the first cause of week jets. Also make sure no ice has formed inside the pump housing causing the impeller to stick. However, there are a couple other things to check first.
If you decide to replace your hot tub pump, look closely at a few things to get a proper match.
A spa pump should run quietly with a slight 'hum'. A pump will not last forever and will eventually have to be replaced. If this is the case then you need to get this fixed! If the noise is coming from the pump motor then this is a sign of internal damage and should also be fixed before the motor seizes. Also look closely at the pump housing for any micro cracks. Replace immediately as this will lead to a larger more serious leak. If you see water dripping from the pump shaft, then this usually signals a leaky pump bearing.
If you see signs of water leakage then you need to look closely and determine where it is coming from.
An efficient pump motor will still be warm to the touch.. Excessive hear means the pump is running inefficiently and costing you lots of money. Vibration of pump motors will quickly Intelligent All-in-one Condensing unit cause a small crack to develop into a big crack. Make sure the power is the same, 120 VAC or 230 VAC. Do you see any signs of water? Is the pump motor louder than normal? Is the motor running excessively hot? If the answer is yes to any of these then it is time to look at replacing or fixing you spa pump. Look inside at the impeller and insure there are no obvious obstructions. Never, never match HP ratings listed on a pump as they are never accurate and often overstated!
Quality pumps come with a premium but are worth the extra investment. Check the o-rings and the couplers to insure they are tight and not leaking
A spa pump has a starting capacitor that gives it extra juice when starting. Is your pump a one speed or two speed pump? Finally, match the amp rating of your pump closely to the amps of another pump. Look for signs of wear and tear and be proactive!
I always suggest you look for signs of wear every time you replace or clean you filter system.
While poor jet performance may be caused by a pump, it is not likely. A spa pump either works or does not work. At this time, have a good look at the spa pump. I would look 1st to a plugged filter or a clogged intake as the first cause of week jets. Also make sure no ice has formed inside the pump housing causing the impeller to stick. However, there are a couple other things to check first.
If you decide to replace your hot tub pump, look closely at a few things to get a proper match.
A spa pump should run quietly with a slight 'hum'. A pump will not last forever and will eventually have to be replaced. If this is the case then you need to get this fixed! If the noise is coming from the pump motor then this is a sign of internal damage and should also be fixed before the motor seizes. Also look closely at the pump housing for any micro cracks. Replace immediately as this will lead to a larger more serious leak. If you see water dripping from the pump shaft, then this usually signals a leaky pump bearing.
If you see signs of water leakage then you need to look closely and determine where it is coming from.
An efficient pump motor will still be warm to the touch.. Excessive hear means the pump is running inefficiently and costing you lots of money. Vibration of pump motors will quickly Intelligent All-in-one Condensing unit cause a small crack to develop into a big crack. Make sure the power is the same, 120 VAC or 230 VAC. Do you see any signs of water? Is the pump motor louder than normal? Is the motor running excessively hot? If the answer is yes to any of these then it is time to look at replacing or fixing you spa pump. Look inside at the impeller and insure there are no obvious obstructions. Never, never match HP ratings listed on a pump as they are never accurate and often overstated!
Quality pumps come with a premium but are worth the extra investment. Check the o-rings and the couplers to insure they are tight and not leaking
Posted by: aircooler at
03:08 AM
| No Comments
| Add Comment
Post contains 634 words, total size 4 kb.
12kb generated in CPU 0.0064, elapsed 0.0353 seconds.
35 queries taking 0.0305 seconds, 46 records returned.
Powered by Minx 1.1.6c-pink.
35 queries taking 0.0305 seconds, 46 records returned.
Powered by Minx 1.1.6c-pink.